Consult your Local Building Department about Permits and Inspections for all Electric Wiring Projects. Getting one of the browns in the wrong place would mean the switch would be controlling other lights on the circuit. Add up the wattages of all light bulbs in the fixture and make sure it is less than the rated capacity of your dimmer switch. Does the fixture itself make a difference? Twist the ends together clockwise and cap them using a wire connector nut. They also save energy and extend the life of your light bulbs. Don't use them with ceiling fans, appliances or fluorescent lights because you will destroy the dimmer and whatever it is connected to.
Then just attach the black wires to different terminals on your single-pole switch and attach the ground wire in the box to the yoke of the switch using the green screw. Tested and this didn't do anything, light didn't even turn on. Ring Varlight first, to verify minimum load. Home electrical wiring is the process of installing electrical wire to a location that will serve electrical devices or an appliance. If both dimmer wires are black, it doesn't matter how you connect the wires. This maybe what caused the lack of dimming if there are other fixtures in the house which can't be dimmed.
The neutral white wire in the box has nothing to do with the switch; it goes directly up to the light. Next turn off the power to the existing switch from the breaker panel and test with a voltage meter. Most dimmers are designed to fit a standard wall box opening, which makes it easy to replace the switch for any incandescent or halogen light with a dimmer. Skill Level: Beginner to Intermediate — Best if wired by a Licensed Electrical Contractor. First, twist the wires together, and then screw on the wire nut. If only one switch controls the light, purchase a single-pole dimmer.
I replaced the switch talking to someone at Home Depot to make sure I did it correctly but the lights still will not dim. Remove ¾ inch of casing from the end of the house wires and the dimmer switch wires, if needed. In addition to posting comments on articles and videos, you can also send your comments and questions to us on our or at 800 946-4420. You can recognize a four-way switch by the two screw terminals on each side. You can now turn the power back on at the breaker and test the dimmer. Name required Email will not be published required Website By submitting you agree to our Home Electrical Wiring and Electrical Repairs Please Note: Unless otherwise posted, please refer to the following Guidelines when working on Electrical Projects: Skill Level: Intermediate to Advanced - Electrical Repairs and Circuit Wiring is Best Performed by a Certified Electrician or Licensed Electrical Contractor.
Tools Required: Basic Electricians Pouch Hand Tools and Voltage Tester. If you have to do this, we suggest keeping the bulb at full power. Tighten a wire nut over each pair of wire ends. Twist the ends together clockwise and cap them using a wire connector nut. With a standard single-pole dimmer, a single switch controls the light.
I'll looked at the Varilight instructions, and it does not state the minimum load, you could ring Varilight to verify. First you must pick a dimmer switch that has the capacity to control the light fixture you would like to dim. Adding a dimmer switch is a perfect way to control the level of lighting when entertaining. Thanks John We want to hear from you! If two switches control a single light or a group of lights, you will need a three-way dimmer. So the correct wiring should be the 2 Brown wires into C and the single brown into L1 assuming only one light is controlled by this switch? My table is 8ft w x 4ft L and extends approximately 40 more inches when opened fully.
So, what type of lamp are you trying to dim? Electrical Tip The Safest Way to Test Electrical Devices and Identify Electric Wiring! Replace a three-way switch with a three-way dimmer. This is all assuming the wiring follows a standard Assuming you have you wiring correct, it may be the single lamp is of an insufficient load to the dimmer to operate. The type and size of the home wiring electrical boxes will depend upon the circuit size, application and its location. Which one do you recommend and how high do I hang it? You could try a reset of factory settings. Dimmer switches are only for use with incandescent lights. I started to review the manual when I found a statement that the chandelier should not be used on a dimming circuit.
. Dimming the bulb, will likely cause erratic behavior such as flickering or buzzing and ultimately may cause damage to the bulb. Just kill the power at the breaker and remove the wire nuts from the black wires connected to the dimmer wires. The dimmer switch must be rated for the amount of watts that will be controlled. Electrical Tools Required: Basic Electricians Pouch of Hand Tools, a Voltage Tester and a Multi Meter.
The larger chandelier is so impressive but I dont know if it would be too large. Name required Email will not be published required characters available. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. I can't say whether the original connection will have broken it. If one dimmer wire is black and the other red, you should splice the black wire to the wire that brings the electricity from the service panel and the red wire to the wire that runs to the light fixture. After reading online I think I've wired it incorrectly first time and broken the dimmer, but just wanting some confirmation from you guys before I go buy another.
Check the rating of the dimmer switch you purchase. Have I wired it right second time, but broken the dimmer by wiring incorrectly first time? Estimated Time: Depends on personal level experience and ability to work with tools. Do not install more than one dimmer on the same circuit. Replace one of those switches with the dimmer. If there is bare wire exposed, unscrew the wire connector, remove the wires, trim the ends of the wires with a wire cutter, and then re-cap the wires.